Decal Application Instructions

Choose the instructions that match your decal and application. Read through the steps before you begin, and take your time with placement. Once applied, decals are intended to stay in place.

Check the conditions before installing: For best results, apply ORACAL vinyl in mild conditions, ideally around 60–80°F. ORAFOL lists a 46°F minimum application temperature for ORACAL 651, 751, and 951; applying close to the minimum can make handling and adhesion less forgiving. Make sure the vinyl and surface are not cold, and that the surface is clean, dry, and fully cured if recently painted. Avoid installing in rain, strong wind, direct hot sun, or when the surface is unusually hot or cold.

For wet installations: Use only on a clean, smooth, nonporous surface. ORAFOL recommends an ambient temperature of at least 60°F and keeping the newly applied graphic in that environment for at least 24 hours. Wet application is not suitable for every ORACAL product or surface, so use the dry method when unsure.

Small Decal Installation

View small decal application steps

You’ll need

  • A clean, dry surface
  • A credit card or application squeegee
  • A clean cloth

Steps

  1. Clean the surface with mild soap and water, then dry it thoroughly. Remove any remaining dust or particles.
  2. Your decal has transfer tape and backing paper. Press firmly over both sides with a credit card or squeegee to help the decal adhere to the transfer tape.
  3. Place the decal face down on a hard surface. Starting at one corner, slowly peel the thicker backing paper away at an angle, keeping it close to parallel with the surface. If the decal stays on the backing paper, lay it back down, press again, and try once more.
  4. Hold the decal with both hands, line it up where you want it, and place the center down first. Slowly lower the sides while pressing the decal onto the surface.
  5. Before removing the backing paper, you can test placement by positioning the decal while its backing is still attached. Once applied, decals are intended to be permanent.
  6. Starting from the center, press outward in all directions to push out air pockets. If using a card, take care not to scratch the surface.
  7. Slowly peel the transfer tape back over itself, keeping it close and parallel to the surface rather than pulling straight up. This helps the vinyl stay in place.
  8. Press over the decal once more, especially around the edges, to help ensure it is fully adhered.

Large Decal Installation

Large decals can be applied using a dry or wet method. The dry method is recommended for most installations. The wet method can help with positioning on very large or complex decals, but requires additional drying time.

Large decal: dry installation (recommended for most installs)

Best for: Flat or lightly curved surfaces, indoor installations, and long-term durability.

You’ll need

  • Masking tape
  • A squeegee, preferably with a felt edge
  • Decal application spray or isopropyl alcohol (70% or higher)
  • A clean, lint-free cloth

Steps

  1. Thoroughly clean the surface with decal application spray or isopropyl alcohol. The surface must be clean, dry, and free of wax, dust, and oils.
  2. Position the decal and use masking tape to hold it in place. Measure and level it before applying.
  3. Create a hinge at the center of the decal by taping across the middle of the top or side, depending on the decal’s shape and orientation.
  4. Lift one half of the decal and slowly peel the backing paper away from the vinyl to expose the adhesive.
  5. When you reach the taped hinge, carefully trim away the peeled backing paper. For large decals, it can help to have another person hold the exposed decal upright while you trim.
  6. Begin applying from the center outward with firm, overlapping squeegee strokes. Leave a small gap near the hinge so you can lift it and remove the backing from the other half.
  7. Once the first half is pressed down, carefully remove the backing paper from the other half and repeat, working from the center outward.
  8. Before removing the transfer tape, make sure the whole decal has been pressed firmly and air bubbles have been worked out.
  9. Slowly remove the transfer tape by pulling it back over itself at a sharp angle, close to 180 degrees.
  10. Re-squeegee any areas that need extra pressure. Use a felt-edge squeegee or your fingers to help avoid scratching the surface.
Important: Do not apply below 50°F or above 90°F. Avoid washing the surface or exposing it to moisture for 24 hours.
Large decal: wet installation

Best for: Very large decals, complex alignment, and installations where careful repositioning is helpful.

You’ll need

  • A spray bottle
  • Decal application fluid, or water with only 2–3 drops of dish soap. Do not use too much soap.
  • An application squeegee, preferably with a felt edge
  • Isopropyl alcohol, if needed to clean the surface
  • A clean cloth

Steps

  1. Clean the surface with application fluid or isopropyl alcohol and allow it to dry.
  2. Place the decal face down and slowly remove the backing paper. If the decal remains attached to the backing paper, lay it back down and press it again with the squeegee.
  3. Lightly mist the receiving surface and the adhesive side of the decal. The goal is to help prevent immediate sticking and allow positioning. Do not soak the decal.
  4. Carefully position the decal. It should remain adjustable while wet.
  5. Once it is positioned, squeegee from the center outward to remove liquid and air bubbles.
  6. Allow the decal to set and dry for at least 10–15 minutes. It may take longer depending on conditions.
  7. Squeegee the decal once more after it has set.
  8. Slowly remove the transfer tape at a sharp angle. If the decal starts to lift, lay the tape back down, press firmly, and try again.
  9. Re-squeegee with a felt-edge squeegee or press down with your fingers if needed. Be careful not to scratch the surface.
Important: Allow 24–48 hours for full adhesion. Do not wash the surface or expose it to heavy moisture during this time. Small bubbles may disappear as moisture evaporates.

Installation Video

Questions about your decal or installation surface? Contact Fast Life Graphics before applying it.

Shopping Cart
Scroll to Top